Standing Seam Metal Roof Installation Begins With Knowing How To Install Eave Trim. It's Installed Before The Standing Seam And After The Metal Roofing Underlayment. Standing seam roof installation video that shows you how to install a standing seam eave detail. Eave flashing is installed before the standing seam panels and after the metal roofing underlayment. This standing seam metal roof installation video will cover: 00:00 How to install eave trim on a standing seam metal roof 01:24 Standing seam eave detail and parts list 01:53 How to layout standing seam eave trim 02:32 How to install fascia wrap on a standing seam roof 04:03 How to install trim cleat on a standing seam roof 04:52 Cutting and finishing eave trim for a standing seam roof installation 06:15 How to overlap eave trim on a standing seam metal roof 07:25 How to fasten eave trim on a standing seam roof This video is intended for installation of a snap lock standing seam that's clip fastened. It's NOT intended for mechanically fastened or nail strip standing seam. If you already have not purchased your metal roofing give us a chance to bid your job. Save 15% to 50% with our manufacturer direct pricing and great customer service. Inexpensive delivery anywhere within the United States. Visit Our WEBSITE https://bit.ly/wsmr-website Visit our LEARNING CENTER http://bit.ly/learning-center-wsmr Standing Seam Eave Detail https://www.westernstatesmetalroofing.com/standing-seam-part-ws-402-bull-nose-drip-eave-trim.html Standing Seam Metal Roof Installation Guide http://www.metalforroofing.com/docs/standing-seam/install_guide_western_lock.pdf?__hstc=187130103.a0187661f72c773f5bf5b6ae0b342094.1589055209040.1604334948812.1604350315970.314&__hssc=187130103.3.1604350315970&__hsfp=3991728011 How to Install Eave Trim With Bullnose Drip Edge In this standing seam how-to, we will walk you through: Laying out your trim. Installing an optional fascia wrap. Installing trim cleat. Cutting and finishing eave trim at gable ends. Overlapping eave trim. Fastening eave trim. Laying Out Your Trim Prior to your layout, it’s good practice to plan the layout of your standing seam panel and trim. Cutting and Finishing Standing Seam Eave Trim at the Gable Ends 1. Measure the distance of trim needed and add one inch for the tab. 2. Mark a 45-degree line at the drip edge. 3. Using metal cutting snips, cut along your outline. 4. When cutting at the tab, cut the corners at a 45 degree. 5. Mark a straight line on the top section for your trim. 6. Continue cutting along your mark. 7. Using a hand seamer, bend the tab downwards 90 degrees. The tab should fall flush with the gable side of your roof. How To Overlap Eave Trim On A Standing Seam Roof NOTE: Overlaps should be six inches. 1. Mark six inches onto your trim. 2. Cut up to the mark at the fold of the trim. 3. At the drip edge, cut the six-inch mark at the hem of the trim. 4. On the adjacent piece, notch cut the hem up to the six-inch mark. 5. Silicone sealant should be applied three inches from the edge. How To Fasten Eave Trim On A Standing Seam Metal Roof 1. First, hook the lower section on the trim cleat. 2. Fasten using pancake screws 12 inches on center. 3. Remove protective plastic coverings upon installation. FOLLOW US ON SOCIAL MEDIA: FACEBOOK: https://bit.ly/facebook-wsmr INSTAGRAM: https://bit.ly/instagram-wsmr TWITTER: https://bit.ly/twitter-wsmr LINKEDIN: https://bit.ly/linkinin-wsmr HOUZZ: https://bit.ly/houzz-wsmr PINTEREST: https://bit.ly/pinterest-wsmr YOUTUBE: https://bit.ly/youtube-wsmr Visit Our WEBSITE https://bit.ly/wsmr-website Visit our LEARNING CENTER http://bit.ly/learning-center-wsmr